|
In this article 1. The calculation most tenders skip 2. Storage or recovery, which one to buy 3. When one tank stops being enough 4. Distribution, dead legs and stored temperature 5. Indicative sizing table and purchase order checklist Related reading: electric water heater manufacturer profile Export background: company profile and export markets Test background: five stage water heater quality control |
|
Quick answer: size hotel water heater capacity by the busiest hour, not by the room count. A 60 room property with 80 percent occupancy and two guests per room, each using 40 litres in the morning peak, needs about 1,900 litres of water stored at 65 degrees if the whole peak lands in one hour. Then add recovery capacity on top, because the tank refills while the next wave of guests wakes up. |
The water heater capacity calculation most tenders skip
Most hotel tenders state a tank volume without showing the arithmetic behind it. The arithmetic is simple and it takes ten minutes, but it changes the answer completely. Start with rooms, apply the occupancy the property actually runs at rather than the brochure figure, multiply by guests per room, then multiply by the litres each guest uses in the peak hour. Showers plus washbasin use plus a safety margin, and the figure lands between 35 and 50 litres per guest for a mid range hotel.
The second step is the one that gets forgotten: that figure is water at outlet temperature, usually around 40 degrees, not water at storage temperature. To convert, use the blend ratio. With stored water at 65 degrees and cold water at 15 degrees, half of the delivered volume is stored hot water and half is cold. So 3,840 litres delivered at 40 degrees needs roughly 1,920 litres held at 65 degrees. Quoting a storage volume that equals the outlet demand double counts the cold water and leaves the property short.
Third step, diversity. Not every guest showers inside the same 60 minutes. A realistic diversity factor for a leisure hotel is lower than for a business hotel with early breakfasts, and a hostel with shared bathrooms behaves differently again. Applying a factor is judgement, not physics, so write it down in the tender and let the buyer agree it, rather than burying it in a supplier calculation.
Storage or recovery, which one to buy
Two properties with the same peak can be served by very different systems. Water heater capacity is a trade between tank size and element bank, and both ends of that trade cost money in different ways. One buyer takes a large tank and a modest element bank, the other a smaller tank and a large element bank. The large tank version survives a long peak without losing temperature, but pays standing loss all day and needs floor space and structural clearance. The large element version recovers fast but draws a heavy electrical load and depends on a supply the building may not have.
The arithmetic for recovery is worth memorising. Lifting one litre from 15 to 65 degrees takes about 0.058 kWh. A 60 kW element bank therefore reheats roughly 1,000 litres per hour, which means 4,000 litres across a four hour overnight window. That number is what tells a buyer whether the tank they have chosen can refill between the evening peak and the morning peak, or whether they are relying on guests not noticing.
| Property type | Indicative storage | Indicative element bank | Feed layout |
|---|---|---|---|
| Serviced apartments per unit | 80 to 100L per unit | 2 to 3 kW per unit | Individual unit, no central plant |
| Small hotel 20 to 40 rooms | 500 to 1,000L | 12 to 24 kW | Single plant room, one bank |
| Mid size hotel 40 to 80 rooms | 1,500 to 2,500L | 36 to 60 kW | Two tanks in parallel, staged |
| Large hotel 80 to 200 rooms | 3,000 to 6,000L | 90 to 150 kW | Cascade bank, duty and standby |
These figures are indicative starting points for a first discussion. Final sizing depends on occupancy, occupancy profile, inlet temperature, distribution losses and the local code.
When one tank stops being enough
A single very large tank has three practical problems: it has to be delivered through a doorway, it has to be replaced as a whole unit, and when it fails the property has no hot water at all. Splitting water heater capacity across two or three tanks in a cascade solves all three. Staged control brings tanks in as demand rises, so the second unit stays cold until the morning peak, and maintenance can take one unit out while the property still runs.
Cascade also helps the electrical design. Instead of one 90 kW load on a single point, the bank is split across circuits, which is easier to protect and easier to phase across a three phase supply. The cost of this design is piping and controls, and that is the trade a buyer should price rather than assume away.
Distribution, dead legs and stored temperature
Water heater capacity is written on the tank, but complaints happen at the shower head. Long dead legs mean the guest waits for hot water, reads it as insufficient capacity, and the hotel buys a bigger tank that does not fix the problem. Insulated pipework and a recirculation loop on a timer solve more complaints per dollar than extra storage does.
Stored temperature is a public health question as much as a comfort question. Many markets expect hot water to be stored at 60 degrees or above and blended down at the outlet to a safe delivery temperature, with the site keeping records of the regime. Whatever the local rule, the controlled blending valve, the thermometers and the recording habit all have to be in the specification, because a storage tank sized correctly but operated at 50 degrees creates a risk nobody priced in. Confirm the applicable guideline with the local health authority before the plant is designed.
Purchase order checklist for project buyers
- Peak hour demand in litres at outlet temperature, with the occupancy and diversity assumptions written down.
- Storage volume at 65 degrees, and the blend ratio used to convert between the two figures.
- Element bank in kW, split across circuits, with the recovery time the buyer expects overnight.
- Number of tanks, cascade control logic and the duty plus standby arrangement.
- Electrical supply available at the plant room, single or three phase, and the maximum demand allowed.
- Insulation thickness on tank and pipework, and whether a recirculation loop is included.
- Thermostat and safety cut out settings, blending valve and the temperature recording routine.
- Certification and documentation set the project consultant requires for handover.
Questions buyers ask most
Do I size on room count or on occupancy
Water heater capacity should be sized on demand, and on the occupancy the property actually achieves in its busiest month. A hotel sold at 95 percent in high season and 40 percent in low season needs a system that handles the high season; sizing on the annual average is how under capacity gets designed in.
Is a bigger tank cheaper than more elements
Usually yes on equipment, no on the whole project. Storage costs floor space, structural support and standing loss every day of the year. Elements cost electrical capacity, which is often the harder constraint in an existing building. Compare the two on total installed cost and on the electrical supply the site can actually deliver.
Can apartment blocks use one central plant
They can, and many do, but billing and maintenance responsibility then sit with the building rather than the tenant. Individual 80 to 100 litre units per apartment avoid metering disputes and keep the failure local. Which model wins depends on how the building is managed, not on the engineering alone.
How ANTO supports project specifications
ANTO has manufactured electric water heaters since 2005, exports to Europe, South America, the Middle East, Africa and Central Asia, and builds more than 200 models across tank, injection and assembly workshops at 20,000 units per month. Project buyers can review the electric water heater products range for storage and commercial configurations, and specify the storage electric water heater platform in the voltage and capacity the site uses. Every finished unit passes 100 percent electrical testing, the factory is ISO 9001 audited, and the inner tank carries a five year warranty with a one percent free spare parts allowance on order volume.
|
Send the room count and occupancy profile and receive a capacity proposal within 24 hours |
Related reading
factory scale and monthly production capacity
certification scope for project handover
|
Author: Technical Support Team, Zhongshan ANTO Electric Appliance Co., Ltd. Electric water heater manufacturing since 2005. Published: 23 November 2026 | Last updated: 23 November 2026 Sizing examples use standard specific heat values and ignore distribution losses. Confirm the final design against local plumbing, electrical and public health requirements. |



